Penco All Welded Lockers |
Please Call 1-800-497-0629 or e-mail: service@maxmaterialhandling.com for price and availability and any other questions you may have.
Penco All-Welded lockers are shipped completely assembled. All components are welded together at the factory prior to being painted with a durable baked-on enamel finish. Doors have a full-length continuous hinge. Locker groups up to 54" wide can be shipped as units, reducing on site installation time to a minimum.
Penco All-Welded lockers are shipped completely assembled. All components are welded together at the factory prior to being painted with a durable baked-on enamel finish. Doors have a full-length continuous hinge. Locker groups up to 54" wide can be shipped as units, reducing on site installation time to a minimum. All-Welded Defiant II Single Point Latch (SPL) Locker Overview Available in 1, 2 and 3 tier models. Same as the All-Welded Lockers except that these lockers have stiffening pans and a full length continuous hinge. For ease of maintenance, there are no moving latch parts. Stainless steel recessed pocket has integral finger grip door pull. Accepts built-in locks or padlocks
Penco All-Welded Locker Specifications
MATERIALS: SHEET STEEL: All parts made from prime grade mild cold rolled sheet steel free from surface imperfection, and capable of taking a high grade enamel finish.
FINISHING: Chemically pretreat metal with a six stage cleaning phosphatizing and metal preparation process. Finish coat shall be electrostatically applied powder coat enamel properly cured to paint manufacturer specifications to achieve optimum performance. All lockers shall be painted inside and outside with the same color.
FABRICATION GENERAL: CONSTRUCTION: Fabricate lockers square, rigid and without warp. Metal faces shall be flat and free of distortion. Lockers shall be pre-assembled of welded construction, all welds shall be free of burrs. Grouping shall be the most practical that conforms to the job requirement. No bolts, nuts or rivets shall be allowed in the assembly of main locker groups. Each locker group shall be securely welded into a one piece structure.
SIDE AND DOOR FRAME: Shall be manufactured from 16 gauge steel. The front edge of the frame shall be formed to a channel shape with a continuous door strike. Two and three tier lockers shall have intermediate 16 gauge channel shaped horizontal frame members attached to the side frames with mortise and tenon construction, and securely welded. Intermediate frames shall consist of two 16 gauge frame channels securely welded together.
TOPS: Shall be 16 gauge notched and formed. Each group of lockers shall have one continuous flat top.
BOTTOMS: Shall be 16 gauge notched and formed. Each group of lockers shall have one continuous bottom suitable for anchoring to wood or concrete bases.
SHELVES: Shall be 16 gauge, flanged on four sides with an additional return flange on the front edge to increase strength.
BACKS: Shall be solid 18 gauge cold rolled steel. One piece steel backs for groups to 48" wide. Groups over 48" wide shall have two piece backs.
DOORS: Doors 20" or higher shall be formed from one piece 14 gauge cold rolled sheet steel. Formations shall consist of a full channel shape on the lock side of adequate depth to fully conceal the lock bar, channel formation on the hinge side, and right angle formations across the top and bottom. Doors over 15" wide and over 30" high shall have a 3" wide 20 gauge full height reinforcing pan welded to the inside face of the door on 6" centers. Doors for box lockers 4, 5, 6, 8 & 9 tiers high shall be 14 gauge steel and have channel formations on lock side and hinge side and have right angle flanges on the top and bottom.
DOOR HANDLE & LATCHING 1, 2 & 3 TIER: Handles shall be recessed in the door and be finger lift control. The 20 gauge drawn pocket shall be brushed stainless steel securely fastened to the door with two tabs plus a positive tamper resistant decorative fastener. The pocket shall be of sufficient depth to prevent a combination padlock, built-in combination lock or key lock from protruding beyond the face of the door. A lock hole cover plate shall be provided for use with padlocks. The lifting piece shall be 14 gauge formed steel, attached to the latching channel with one concealed retaining lug and one rivet assuring a positive two point connection. Handle finger lift shall have a padlock eye for use with a 9/32" diameter padlock shackle. It shall have a sound deadening molded comfortable finger lift. Doors to have latch clip engaging the door frame at three points on 60" & 72" high and two points on 20" through 36" high doors. Locking device to be positive, automatic type, whereby locker door may be locked when open, then closed without unlocking. One rubber silencer shall be firmly secured in the frame at each heavy gauge latch hook. Latch clips shall be glass filled nylon for long life and low friction and shall hold doors shut by engaging the latch hooks. Latch hooks on diamond-perforated lockers shall have tamper guards. The latch channel assembly shall be quieted by the use of unique nylon glides to reduce noise.
DOOR HANDLE & LATCHING 4 TO 9 TIER BOX LOCKERS: Doors shall be punched for use with padlocks or built-in locks. Doors for use with padlocks shall be equipped with an 18 gauge combination door pull, staple and lock hole cover plate with integral friction catch.
VENTILATION: All sides and doors 20" or higher shall be perforated with diamond-shaped openings 3/4" wide x 1-1/2" high in a quantity and pattern to insure maximum ventilation and maintain structural strength. All other doors shall have small diamond-shaped perforations 7/16" wide x 15/16" high.
NUMBER PLATES: Each locker to be supplied with a polished aluminum number plate, 2-1/4" wide x 1" high, with black numerals not less than 3/8" high. Number plates shall be attached to the face of the door with two aluminum rivets.
HINGES: 16 gauge continuous type hinge is welded to the door and riveted to the frame for the full height of the door.
INTERIOR EQUIPMENT: Single tier lockers 48-1/2" or higher shall have one hat shelf located approximately 9" down from the top of the locker. Lockers 20" or more in height and up to 15" wide to be supplied with one double prong ceiling hook and two single prong wall hooks, over 15" wide to be supplied with a double prong ceiling hook and four single prong wall hooks. All coat hooks shall be forged steel with ball ends, zinc plated.
LOCKER OPTIONS: Continuous metal base: If required base shall be 4" high 16 gauge, integral with locker bottom.
Legs: If required, each group of lockers shall be furnished with four 14 gauge legs each 4" high and welded to the locker bottom.
DOORS: Box locker doors 4 to 9 tier, as an alternative option each door shall be furnished with a stainless steel padlock strike.
DOOR HANDLE & LATCHING 4 TO 9 TIER BOX LOCKERS: As an alternate option, each door shall be provided with a finger operated 11 gauge slam latch with an electrogalvanized trigger, and a spring contained in a 14 gauge case welded to the door. The spring latch engages a 13 gauge hasp welded to the frame. Rubber bumpers shall be securely installed in the frame.
VENTILATION: If specified, all perforations may be deleted. If deleted, louvers may be added to the doors.
DOOR VENTILATION: Delete diamond perforations in the doors and substitute with standard louvers, or mini louvers may be substituted and shall be 5/8" wide x 1/4" high. Louvers shall be placed in doors in manufacturer's standard pattern.
ADA LOCKERS: Handicap lockers shall have recessed handles and shall be single tier or the lower opening of a double tier locker. Locker bottom shall be a minimum of 9" off the floor, or an extra shelf placed 9" off the floor. Single tier lockers shall have a shelf 48" off the floor. Doors assigned for handicapped use shall have an appropriate symbol sign.
ACCESSORIES: For accessories see Accessory Specifications.
EXECUTION: INSTALLATION: Install metal lockers at location shown in accordance with manufacturers instructions for plumb, level, and flush installation. ANCHOR LOCKERS to the floor and wall 36" on center or less as recommended by the manufacturer. INSTALL SLOPING HOODS AND METAL FILLERS using concealed fasteners. Provide flush hairline joints against adjacent surfaces. INSTALL BENCHES by fastening bench tops to pedestals and securely anchoring to the floor using appropriate anchors for the floor material. ADJUST & CLEAN: Adjust doors and latches to operate without binding. Verify that latches are operating satisfactorily. TOUCH UP marred finishes with factory supplied paint.
ALL-WELDED DEFIANT II
SINGLE POINT LATCH SPECIFICATIONS When specifying All-Welded Lockers with Defiant II Single Point Latch (SPL) doors, substitute the following specifications for "Doors", "Door Handle & Latching, 1, 2 & 3 Tier", "Ventilation" and "Hinges" to the All-Welded specification above. Delete "Door Handle & Latching 4 to 9 Tier Box Lockers."
DOORS: All doors shall be formed from one piece 14 gauge steel. Formations shall be channel shape on the hinge and latch sides, and right angle formations across the top and bottom. Top and bottom flanges shall have one 90 degree bend. The latch side formation shall include a slot to fully engage an additional anti-pry lug integral with the padlock hasp limiting motion in any direction. On doors measuring 12” through 18” wide, additional reinforcement shall be in the form of a vertical 18 gauge pan measuring 3-1/2” wide MIG-welded to the top and bottom flanges and hinge side channel, with an additional ½“ flange spot welded a maximum of 8" on center to the door skin to maximize door rigidity. Doors measuring more than 18” wide shall be reinforced using a 20 gauge horizontal box pan MIG-welded a maximum of 8" on center to the hinge and latch side channels, and spot welded a maximum of 8" on center to the door skin along the upper and lower pan edge for optimum strength, quiet operation and stiffness. Door shall be manufactured to allow ventilation and stiffness.
HINGES: 16 gauge continuous hinges (full length of the door) are welded to the door and riveted to the frame.
DOOR HANDLE & LATCHING 1, 2 & 3 TIER: Handles shall be recessed in the door. The formed pocket shall be brushed stainless steel securely fastened to the door with two lugs plus a positive tamper resistant fastener. The pocket shall be of sufficient depth to prevent a combination padlock, built-in combination lock or key lock from protruding beyond the face of the door. An anti-pry lock alignment bracket shall be supplied for use with built-in combination locks to facilitate installation, adjustment and to increase resistance to prying by engaging the hasp assembly. A lock hole cover plate shall be provided for use with padlocks. All pockets shall be 22 gauge drawn stainless steel for superior strength. Door pull shall be formed in the pocket. Pocket and pull shall be integral. Doors shall have a catch to retain unlocked doors in the closed position. Locking shall be accomplished by an 11 gauge lug welded to the locker frame. The lug shall include a surface for the bolt of a built-in combination or key lock to engage. A padlock staple shall protrude through the 22 gauge pocket. The hasp assembly shall include an additional lug that mechanically engages a slot on the latch side door formation preventing the spreading of the door from the frame channel. An integral angle shall brace the lock hasp against the locker side sheet to prevent twisting of the frame. Rubber door silencers shall be firmly attached to the locker frame.
VENTILATION: All side frames and doors 20" or higher shall be perforated with diamond-shaped openings 3/4" wide x 1-1/2" high in a quantity and pattern to insure maximum ventilation and maintain structural strength.
Please Call 1-800-497-0629 or e-mail: service@maxmaterialhandling.com for price and availability and any other questions you may have. |
|
|
