Penco Angle Iron | Penco's new Angle Iron Welded Locker is designed for long life and trouble free operation under the most demanding ahletic and corridor conditions. Built within a 1" x 1" x 1/8" angle iron frame this 1/8" thick angle iron exoskeleton creates extra strong locker edges and provides a solid framework. Diamond perforated doors and sides offer a high degree of air flow.
Lockers are built in groups with the top, bottom and back panels spanning multiple lockers, which reduces seams and adds rigidity
Options and Accessories:
Penco Angle Iron WeldedLocker Specifications
Overview Available in 1, 2, and 6 tier models. Doors are 14 gauge. For 1 and 2 tier lockers, there is a choice between single point latch doors with stainless steel pockets, and 3-point latching with a cremone turn handle. Tops and bottoms are made of solid 16 gauge cold rolled steel. Perforated sides and perforated intermediate partitions are constructed of 14 gauge diamond perforated metal for ventilation. Materials SHEET STEEL: All parts made from prime grade mild cold rolled steel free from surface imperfection and capable of taking a high grade pure polyester powder coat finish.
FINISH: Chemically pretreat metal with a six stage cleaning phosphatizing and metal preparation process. Finish coat shall be electrostatically applied powder coat enamel properly cured to paint manufacturer specifications to achieve optimum performance. All lockers shall be painted inside and outside with the same color.
Fabrication, General
CONSTRUCTION: Fabricate lockers square, rigid and without warp. Metal faces shall be free of distortion. Lockers shall be of welded construction and all welds shall be free of burrs. Grouping shall be the most practical that conforms to the job requirements. No bolts, nuts, or rivets shall be allowed in the assembly of main locker groups. Each locker group shall be securely welded into a one-piece structure.
FRAMING SYSTEM: Frames shall be made of continuous 1" x 1" x 1/8" pretreated (to remove scale) angle iron steel.
SIDES AND INTERMEDIATE PARTITIONS: 16 gauge solid, or 14 gauge diamond-perforated, as required.
FORMED DOOR: 1, 2 and 6 tier doors shall be constructed of solid 14 Ga. cold rolled steel with double bends on vertical sides and a single bend on horizontal sides.
TOPS, SHELVES: Shall be made of solid 16 Ga. cold rolled sheet steel free of surface imperfections.
BOTTOMS: Shall be made of solid 16 Ga. cold rolled sheet steel with front to back 16 Ga. spacer channel welded to locker bottom [when closed bases are not used] for easier and more secure installation.
Latching Options 1 & 2 tier: DEFIANT II SINGLE POINT DOOR (doors 20” or higher): Provide an unbreakable stationary 11 gauge latch welded to locker frame, extending no more than 1-1/4” into the locker opening. A stainless steel recessed pocket is mounted to a 14 gauge 3.5" wide 18 gauge reinforcing pan welded to the inside of the door on the hinge side. Doors measuring wider than 18” shall feature a 20 gauge, horizontal box pan MIG welded to the hinge and latch side formations, and spot welded to the door skin at top and bottom for optimum strength. Door latch and recessed pocket assembly shall be capable of accepting either padlock or built-in combination lock. Handles shall be recessed in the door. The formed pocket shall be brushed stainless steel securely fastened to the door with two lugs plus a positive tamper resistant fastener. The pocket shall be of sufficient depth to prevent a combination padlock, built-in combination lock or key lock from protruding beyond the face of the door. An anti-pry lock alignment bracket shall be supplied for use with combination locks to facilitate installation and adjustment. A lock hole cover plate shall be provided for use with padlocks. All pockets shall be 22 gauge drawn stainless steel for superior strength. Door pull shall be formed in the pocket. Pocket and pull shall be integral. Locking shall be accomplished by an 11 gauge lug welded to the locker frame. The lug shall include a surface for the bolt of a built-in combination or key lock to engage. A padlock staple shall protrude through the 22 gauge pocket. The hasp assembly shall include an additional lug that mechanically engages a slot on the latch side door formation preventing the spreading of the door from the frame channel. An integral formation shall brace the lock hasp against the locker side sheet to prevent twisting of the frame Rubber door silencers shall be firmly attached to the locker frame.
BOX LOCKERS Doors shall be punched for use with padlocks or built-in locks. Doors for use with padlocks shall be equipped with an 18 Ga. combination door pull staple and lock-hole cover plate with integral friction catch. VENTILATION DOORS: Doors 20” or higher shall be perforated with diamond shaped openings ¾” wide x 1-1/2” high. Other doors shall have small shaped perforations 7/16” wide and 15/16” high.
NUMBER PLATES: Each locker door shall be supplied with a polished aluminum number plate 2-1/4” wide x 1” high, with black numerals not less than 3/8” high. Number plates shall be attached to the face of the door with two aluminum rivets.
HINGES: Doors shall be hinged on the right side with 3” five knuckle 14 Ga. fast pin heavy-duty butt hinges. Provide three hinges on each single tier door and two hinges on each 2 through 6 tier doors. Hinges shall be welded to both door and locker frame.
INTERIOR EQUIPMENT: Single tier lockers 48-1/2” or higher shall have one hat shelf located approximately 9” down from the top of the locker. Lockers 20” or more in height and 12” or 15” wide shall have one double- prong ceiling hook and two single-prong wall hooks. Lockers over 15” wide shall have a double-prong ceiling hook and four single-prong wall hooks. All coat hooks shall be of forged steel with ball ends, zinc plated.
Locker Accessories:
LOCKS: Built-in or padlocks.
SLOPE HOODS: Available in six-foot sections.
Options
DOOR HANDLE & LATCHING 1 & 2 TIER (ADA Compliant): Handles shall be recessed in the door and be finger lift control. The 22 gauge drawn pocket shall be brushed stainless steel securely fastened to the door with two tabs plus a positive tamper resistant decorative fastener. The pocket shall be of sufficient depth to prevent a combination padlock, built-in combination lock or key lock from protruding beyond the face of the door. A lock hole cover plate shall be provided for use with padlocks. The lifting piece shall be 14 gauge formed steel, attached to the latching channel with one concealed retaining lug and one rivet assuring a positive two point connection. Handle finger lift shall have a padlock eye for use with a 9/32" diameter padlock shackle. It shall have a sound deadening molded comfortable finger lift. Doors to have latch clip engaging the door frame at three points on 60" & 72" high and two points on 20" through 36" high doors. Locking device to be positive, automatic type, whereby locker door may be locked when open, then closed without unlocking. One rubber silencer shall be firmly secured in the frame at each heavy gauge latch hook. Latch clips shall be glass filled nylon for long life and low friction and shall hold doors shut by engaging the latch hooks. Latch hooks on diamond-perforated lockers shall have tamper guards. The latch channel assembly shall be quieted by the use of unique nylon glides to reduce noise.
HINGES: 16 gauge continuous hinges (full length of the door) are welded to the door and riveted to the frame.
INTEGRAL BASE: Provide a 4” high 14 Ga. welded steel base enclosed on all four sides securely welded to locker bottom.
Ventilation SIDES: Sides and intermediate partitions are constructed with 13 Ga. ¾” flattened expanded metal securely welded to frame at intervals not to exceed 6”. DOORS: If specified, all perforations may be deleted. If deleted, louvers or mini louvers may be added to the doors.
Execution INSTALLATION: Install metal lockers at location shown in accordance with manufacturer’s instructions for plumb, level, and flush installation. Anchor lockers to the floor and wall 36” on center, or less as recommended by the manufacturer. Install sloping hoods and metal fillers using concealed fasteners. Provide flush hairline joints against adjacent surfaces. Install benches by fastening bench tops to pedestals and securely anchoring to the floor using appropriate anchors for the floor material. Lifetime Limited Warranty Locker manufacturer shall warrant the locker for the lifetime use of the original purchaser from the date of shipment. Warranty shall include all defects in material and workmanship, excluding finish, vandalism, and improper installation. |
|
|
